SYSTEM Automotive

Aptiv’s Third Generation of 77 GHz-Based Short-Range Radar (SRR3)
- Published
- 17/10/2018
- Product code
- SP18432
- Price
- EUR 3490
- Applications
- Automotive
The first highly integrated 77 GHz short range radar sensor for advanced driver assistance systems with a single receive-transmit MMIC bare die from Infineon found on the market.
This year, we have seen radar applications use two frequencies, 24 GHz and 77GHz. For a long time, 24 GHz has been dedicated to Short Range Radar (SRR) detection applications like Blind Spot Detection (BSD) or Rear Side Detection (RSD). But due to spectrum regulations, the 24 GHz ultra-wide band (UWB) will soon phase out in Europe and the USA. This, and the need for higher performance in emerging radar applications, makes 24 GHz unattractive. And now manufacturers have turned their interest to the 76-81 GHz band. Aptiv, formerly known as Delphi, has taken a step ahead of its competitors since the first generation of SRR radar by using 77GHz for BSD. Using this band has allowed to Aptiv to propose high resolution and accuracy SRR with even smaller form factor in the third generation, SRR3.
The SRR3 device, FCC certified in 2015, is a side and backside SRR. It is designed for various Advanced Driver Assistance Systems (ADAS) applications such as capturing the blind spot, assisting lane changes and warnings against cross traffic. It features three different PCB substrates with two dedicated to Radio Frequency (RF) signal processing and transmission.
Working in the 76-77 GHz un-licensed band, the device contains forty H-pole planar antennas fed by cavity waveguides. With its small form factor, it could compete with the standard dual board radar modules.
Compared to its competitors, Aptiv is still the only one that uses bare die Monolithic Microwave Integrated Circuits (MMICs) and cavity waveguides. In this module, the innovation is in the single chip from Infineon that integrates four receive (Rx) and two transmit (Tx) channels using SiGe Heterojunction Bipolar Transistor (HBT) technology. And, the RF Printed Circuit Board (PCB) substrate uses glass-reinforced hydrocarbon ceramic laminate, completely PTFE free.
Based on a complete teardown analysis of the Aptiv Radar, the report provides the bill-of-material (BOM) and the manufacturing cost of the radar sensor. The report also includes a complete physical analysis of the MMIC. Also, the complete cost analysis and a selling price estimation are calculated.
Back to top
Overview/Introduction
- Executive Summary
- Block Diagram
- Reverse Costing Methodology
- Company Profile and Main Features
Physical Analysis
- Overview of the Radar
- Views and Dimensions of the Radar
- Radar Opening
- Electronic Boards
- Global View
- High Definition Photo
- Components Markings and Identification
- RF Configuration
- MMIC Physical Analysis
Cost Analysis
- Boards Cross Section
- PCBs Cost
- Estimation of the cost of the MCU
- Estimation of the cost of the MMIC
- BOM Cost – Electronic Board
- BOM Cost – Housing
- Material Cost Breakdown
- Accessing the Added Value (AV) cost
- Electronic Board Manufacturing Flow
- Details of the Housing Assembly
- Added Value Cost Breakdown
- Manufacturing Cost Breakdown
Estimated Price Analysis
- Estimation of the Selling Price
- Automotive Radar Comparison 2018
- Delphi Volkswagen T-Roc MIB2 Discover Media Unit
- Ainstein K-77 Long Range Radar featuring Calterah CAL77A2T4R FOWLP Transceiver
- Piezoelectric Material From Bulk to Thin Film – Comparison 2019
- Ford Focus SYNC 3 Silverbox
- Texas Instruments AWR1843AoP 77/79 GHz Radar Chipset
- LG Electronics Cluster and Infotainment Display Module in the Mercedes-Benz A-Class
- Acconeer A111 60 GHz Pulsed Coherent Radar
- Valeo SCALA Laser Scanner
- Ainstein T-79: Automotive 79GHz Short Range Radar